Meridian Roof Pros provides professional chimney flashing in Meridian, ID for residential and commercial properties across the Treasure Valley. Chimney flashing is a two-part assembly and the failure is almost always that somebody installed one part. Step flashing goes under the shingles and up the brick. Counterflashing gets cut into a mortar joint and laps over the step. A bead of sealant is neither one.
Most Meridian houses do not have a masonry chimney at all. They have a framed chase carrying a metal flue with a factory storm collar, which is a completely different repair. The leak there is usually the chase cap or the siding-to-roof transition, and no mortar is involved anywhere in the fix. We will tell you which one you have before quoting, because the prices are not close.
On real masonry we cut a reglet into the mortar joint with a grinder, tuck the counterflashing an inch into it, wedge it and repoint the joint. Surface-mounted counterflashing sealed to the face of the brick is what the last contractor did, and it is the reason you are telephoning us now, usually three or four winters after the sealant was applied and has shrunk away from the masonry.
The high side of any chimney wider than roughly two feet gets a cricket. That is a framed saddle on the high side, pitched to throw runoff past both corners instead of ponding behind the brick. Code requires one at thirty inches of width. We build them below that width too, because the cost is trivial next to opening a wall later to chase the water.
A chimney reflash usually lands somewhere between twelve hundred and two thousand dollars, which puts it directly on Idaho's registration threshold. We are registered and insured regardless of which side it falls on, and the certificate and the written scope arrive with the estimate whether the statute demands them or not. The price does not move depending on which side of the threshold the job lands, because the work is the same work.
We do not do masonry rebuilds of any kind. If brick is spalling above the roofline or the crown has cracked through, that is a mason's work and we will say so plainly, flash to whatever they build, and sequence the two trades so nobody ends up working over finished work or blaming the other one for a leak.
Our licensed and insured team brings the right materials and equipment to every job — 24-gauge Kynar 500 standing seam panels on floating clips, laminated architectural shingles meeting ASTM D3462, 60-mil TPO laps probed with a blunt seam probe after cooling, tapered polyisocyanurate over metal deck, counterflashing set into a ground mortar reglet, self-adhering membrane in valleys and at every penetration — and backs the work with a written workmanship warranty. We serve Meridian and nearby communities including Boise, Nampa, Caldwell, Eagle.
What We Handle
Everything our chimney flashing in Meridian covers
One crew, one point of contact, and the full range of chimney flashing work in Meridian, ID. If it is on this list we do it in house rather than handing it to a subcontractor:
- chimney flashing repair meridian id
- chimney leak roof ada county
- counterflashing mortar reglet idaho
- step flashing chimney meridian
- chimney cricket saddle treasure valley
- chase cap leak meridian idaho
- chimney reflash cost meridian
- masonry chimney roof leak idaho
- metal flue storm collar meridian
- chimney flashing replacement treasure valley
- roof to wall flashing idaho
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Meridian services.
Materials, equipment and how we do chimney flashing
The difference between chimney flashing that lasts and chimney flashing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with 24-gauge Kynar 500 standing seam panels on floating clips, laminated architectural shingles meeting ASTM D3462, 60-mil TPO laps probed with a blunt seam probe after cooling, tapered polyisocyanurate over metal deck, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Meridian job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in the Treasure Valley means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do chimney flashing outside Meridian
Meridian Roof Pros covers Meridian and the surrounding communities of the Treasure Valley. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Chimney Flashing in Boise, ID — Ada County, population 235,684
- Chimney Flashing in Nampa, ID — Canyon County, population 100,200
- Chimney Flashing in Caldwell, ID — Canyon County, population 59,996
- Chimney Flashing in Eagle, ID — Ada County, population 30,346
- Chimney Flashing in Kuna, ID — Ada County, population 24,011
- Chimney Flashing in Garden City, ID — Ada County, population 12,316
Start on the Meridian Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Meridian Chooses Meridian Roof Pros
- ✓We write the Idaho Code 45-525 lien disclosure on every residential job, including the ones under two thousand dollars where the statute does not require it
- ✓Supplier lien waivers are standard on our invoices rather than an option you have to ask for and fund yourself
- ✓Deck repair and fascia replacement are priced per sheet and per foot in the written scope, so nothing is negotiated on your driveway mid tear-off
- ✓We sell paid inspections you are free to hand to a competitor, because an inspection given away free is funded by whatever it turns up
The standards behind chimney flashing
Quality here is not a matter of opinion — it is written down. The chimney flashing work we do in Meridian follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every chimney flashing project in Meridian gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free chimney flashing free estimate in Meridian, or request a quote and we'll get right back to you.